Scheda programma d'esame
SPACECRAFT STRUCTURES AND MECHANISMS
MARIO ROSARIO CHIARELLI
Academic year2020/21
CourseAEROSPACE ENGINEERING
Code666II
Credits12
PeriodSemester 1 & 2
LanguageEnglish

ModulesAreaTypeHoursTeacher(s)
SPACECRAFT STRUCTURES AND MECHANISMSING-IND/04LEZIONI120
MARIO ROSARIO CHIARELLI unimap
Obiettivi di apprendimento
Learning outcomes
Knowledge

The student who successfully completes the course will be able to demonstrate a good knowledge of both mechanical and technological aspects that refer to the space structures and to the mechanisms; will be aware of fatigue and fracture mechanics of metallic materials; will be able to solve problems of mechanics and will be able to prepare a technical report at the end of a project exercise. The evaluation is based for a 50% on the verification executed during the examination (written and oral). The other 50% is based on the evaluation of the project report that a single student or a group of students will produce at the end of the course before the examination phase.

Assessment criteria of knowledge

The evaluation is based primarily on the verification of the basic knowledge necessary for the design of aerospace structures and mechanisms (strenght analysis, fatigue, fracture mechanics, joints, bearings, gears). The uncertainty of these skills is not allowed. The student must demonstrate the ability to put into practice and to execute, with critical awareness, the design methods and the verification procedures illustrated during the course. For this reason the discussion of the project report will take an important part of the examination phase.

The examination is based on the solution of written exercises and on a subsequent discussion of the results.

Skills

basic skills for the mathematical formulation (modeling of) of physical and/or technical problems

basic skills in planning of a spacecraft (space vehicle) design process

basic skills for problem solving in the field of aerospace engineering

Modalità di verifica delle capacità

 

 

Assessment criteria of skills

during the lesson period the teacher suggests that students solve some simple structural dynamics problems and fatigue and/or fracture mechanics of metallic materials

the periodic meetings, which take place during the development of each project, provide good opportunities to increase the technical preparation of students and to define concrete training objectives

at the same time, the development and preparation of the project report allows the teacher to highlights personal preparation and/or personal gaps of each student

Behaviors

it is suggested to the students to follow the lessons with assiduity both in the first period and in the second period

Assessment criteria of behaviors

the experience of the teacher allows to identify the students who have shown little commitment during the lessons and to define a preliminary framework for the assessment of the preparation of each student

Prerequisites

statics of mechanical systems

theory of beams - basic knowledge on the theory of plates and shells 

computation of characteristics (forces and moments)

basic knowledge on the stress analysis

basic knowledge on buckling phenomena

basic knowledge on kinematics and dynamics of discrete systems

basic knowledge on the dynamics of mechanical systems

basic knwoldge on thermal analysis

basic knowledge on the materials technology

Teaching methods

Theoretical lessons and, in the second period, use of personal computer for the preparation of Finite Element models by Ansys Workbench environment.

periodic meetings during the development of the project work (in general each project will be produced by a team of students two-three)

 

Syllabus

Course Contents

 

( I ) October-December

 

Notes about the design process of a spacecraft.

The launch phase: preliminary examination of acoustic and vibration loading conditions

Random vibrations analysis.

Vibro-acoustic Response Analysis.

Reliability of components and structures: basic definitions and applications.

Strength analysis: definition of the limit loading condition and ultimate loading condition (yielding and collapse of structures).

 

( II )  February-April

 

Computer Lab (ANSYS Workbench)

Welded joints.

Fastened joints.

Fatigue.

S-N curves.

The Goodman diagram for ductile materials.

Effect of the stress concentration.

Fatigue crack growth: basic notes on fracture mechanics.

 

( III ) May

 

Computer Lab (ANSYS Workbench)

Contact stresses: discussion of results of the Hertz theory.

Springs (basic notes)

Bearings.

Spur gears.

Gear trains (basic notes)

Rotating shaft dynamics: critical speeds computation.

Bibliography

Recommended reading includes the following books and/or technical documentation:

 

T.P. Sarafin "Spacecraft Structures and Mechanisms - From Concept to Launch"

 

R.C. Juvinall & K.M. Marshek "Fundamentals of Machine Component Design"

 

ESA Spacecraft mechanical loads analysis handbook -  ECSS-E-HB-32-26A, 19 February 2013

 

ESA Buckling - ECSS-HB-32-24A, 24 March 2010

 

NASA TM-X-73305 - Astronautic Structures Manual - Vol I - Vol II - Vol III, 1975

 

NASA-HDBK-7008 - SPACECRAFT DYNAMIC ENVIRONMENTS TESTING, 2014

 

Jacob Job Wijker - Spacecraft Structures, Springer, 2008

 

Lectures of Spacecraft Structures and Mechanisms (notes) - M. Chiarelli (e-learning)

 

Please visit the website www.ecss.nl to consult all the technical documentation produced by ESA

Non-attending students info

the missed attendance of the lessons can cause considerable difficulties in the development of the preparation itself, in the understanding and development of the simple mechanical exercises proposed during the year and finally in the preparation and development of the project work

Assessment methods

The exam concerns:

a) during the exam the teacher performs the revision of the project report and a suitable discussion of methods, results, technical solutions provided in the report can be part of the exam itself (50%-60% of total score)

b) students must solve at least two technical exercises (possible topics: spacecraft environments, deterministic or random dynamics of discrete and/or continuous system, statistical approach for the definition of loads and strength requirements, simple applications of stress analysis and verification criteria for mechanical systems, bolted joints, welded joints, fatigue of metallic materials, fracture mechanics of metallic materials, contact stress theory, basic notes on gear analysis, critical speeds of rotating shafts (40%-50% of total score)

in general the exam has a duration of two or three hours

 

Updated: 18/09/2020 12:16